In the United States, standards for most softwood plywood are established by the American Plywood Association in cooperation with the National Institute of Standards and Technology. A Voluntary Product Standard for plywood became effective November 1, 1966, and was revised in 1974 and again in 1983.
The mark “PS 1-83” indicates that the panel conforms to the Product Standard published in 1983, which was still in force in 1992. [Commercial Standards (such as CS45-60, “Douglas Fir Plywood.”]
Panels are stamped with a grade mark, unless such a stamp would deface a high quality surface that might be given a natural finish. Such grades are marked on the edges.
Lumber yards usually carry 4 foot by 8 foot and 4 foot by 10 foot panels, but will cut half and quarter sheets. Other sizes are manufactured, almost always in increments of 12 inches, for example, in widths of 36″, 48″ and 60″, and in 9 foot lengths.
The exception to the whole feet rule are panels marked “sized for spacing,” which are slightly shorter than normal panels (e.g., 48 inches by 95½ inches instead of 48 inches by 96 inches) in order to leave space between panels in, for example, sheathing a roof with rafters on 24" centers. The space is necessary to allow for the panels' expansion.
Thicknesses of sanded panels range from ¼ inch to 1¼ inch or more, in steps of 1/8 inch. The thickness tolerance is ± ¹⁄64 inch for panels ¾ inch or less and ± 3% of specified thickness for thicker panels.
Nominal thicknesses of unsanded panels range from 5⁄16 inch to 1¼ inch or more, ± ¹⁄32 inch for panels with a specified thickness of 13⁄16 inch or less, and ± 5% for thicker panels.
|B||Shims, circular repair plugs, and tight knots as large as 1 inch measured across the grain are permitted, as well as minor splits.|
|C plugged||Splits may be no wider than 1/8 inch, and knotholes and borer holes no larger than ¼ inch by ½ inch. Some broken grain is allowed.|
|C||Tight knots as large as 1½ inch, discoloration and sanding defects that do not affect strength, and stitching are permitted.|
|D||Knots and knotholes as wide as 2½ inch measured across the grain and even larger (within limits) in other directions. Splits and stitching permitted.|
A number from 1 to 5, with wood from the species of trees in group 1 being the strongest and stiffest (such as beech, Douglas Fir from certain states) and 5 the least stiff and strong (basswood, poplar).
|Exterior||Panels intended to exposure to the weather. D grade veneer may not be
used in Exterior panels.
Contrary to a common misconception, CDX is not an exterior panel.
Exterior plywood is not necessarily the best choice where plywood will be constantly exposed to the weather; plywood pressure-treated with preservative would probably be better.
|Exposure 1||The glue is the same as that used for Exterior plywood, but other characteristics that affect bonding are not. These panels are for use in high moisture condition or where, during construction, long delays may be expected before the panel is protected from the elements.|
|Exposure 2||Same glue. The wood itself is a bit worse and the panel less rugged.|
|Interior||A different glue is used. Plywood in the other exposure classifications can act as a vapor barrier if glued and nailed; interior plywood cannot. For use only in protected areas indoors.|
Panel grade is either
Certain designations are trademarked by the APA, such as “APA Rated Sheathing,” “APA Rated Sturd-I-Floor,” and “APA Rated Siding.” These panels are marked with span ratings, which indicate the maximum center-to-center distance, in inches, between the joists or studs to which the panel is fastened during construction.
In the case of sheathing, the span rating is two numbers separated by a slash:
In both cases the rating assumes that the long dimension of the plywood crosses at least three supports.
Copyright © 2000 Sizes, Inc. All rights reserved.
Last revised: 11 August 2004.